What's wrong with this picture :(
- Thread starter RojoRacing
- Start date
RojoRacing
Donut Powered Wise-guy
RojoRacing
Donut Powered Wise-guy
RojoRacing
Donut Powered Wise-guy
ccf
Guru
@RojoRacing, sorry to get your hopes up. With it just sitting on the trainer I had forgot about those cracks. I'm heading down to the Hellyer velodrome in a few minutes. I'll check in later to see what you decide.
ratz
Wielder of the Rubber Mallet
I have two Larges, mounted on V20's so I'm not impaired if I ship one out to you.
You want the one on my Trainer is has less pre-existing holes. Condition is as follows
1) Two holes on the front for mounting to the wings you'll need to reuse and drill yours using my sloppy first attempts. I use velcro at the shoulder so no holes on that end.
2) 6 holes for mounting head resets. 4 for the ADEM rest and 2 for the Thor head rest.
3) This one one of Greg early seats it has a couple of epoxy imperfections that need some finger nail polish to clean up; since it's indoors on the training 24x7 I never bothered.
(The road one had better epoxy but it's full of holes from testing different devices mounted the the bike;. that one deserves to retire to the trainer any how.
Greg is sending me Tailboxes; he could send the seat at the same time.
I can strip it down to tonight but I'll need to get home depot tomorrow to get a box big enough to ship it in.
After insurance is done; you should ship that RED on to Greg so he can make a form fitted seat going forward
PM me the shipping address if that sounds good.
I can include the adem head rest if you like they are easy to get but sometimes take a few weeks.
You want the one on my Trainer is has less pre-existing holes. Condition is as follows
1) Two holes on the front for mounting to the wings you'll need to reuse and drill yours using my sloppy first attempts. I use velcro at the shoulder so no holes on that end.
2) 6 holes for mounting head resets. 4 for the ADEM rest and 2 for the Thor head rest.
3) This one one of Greg early seats it has a couple of epoxy imperfections that need some finger nail polish to clean up; since it's indoors on the training 24x7 I never bothered.
(The road one had better epoxy but it's full of holes from testing different devices mounted the the bike;. that one deserves to retire to the trainer any how.
Greg is sending me Tailboxes; he could send the seat at the same time.
I can strip it down to tonight but I'll need to get home depot tomorrow to get a box big enough to ship it in.
After insurance is done; you should ship that RED on to Greg so he can make a form fitted seat going forward
PM me the shipping address if that sounds good.
I can include the adem head rest if you like they are easy to get but sometimes take a few weeks.
jond
Zen MBB Master
Heck another example of a cyclist dehumanised. It’s hard to stay reasonable in the face of such discrimination. Makes me so pointlessly angry.
Our cycling stats in Australia since mike halls death has seen an 80% increase in deaths. In Australia cyclists are seen as less than human.
In Canberra our capital city a trial is to begin. Of police officers on bicycles in plain clothes whom will radio the police vehicle up ahead for close passes by motorists.
Good you’re okay rojo. Lucky.
Training rides fly 6 and 12 cameras. For posterity.
Seemingly in lands where the car came first it’s screw the cyclist.
Our cycling stats in Australia since mike halls death has seen an 80% increase in deaths. In Australia cyclists are seen as less than human.
In Canberra our capital city a trial is to begin. Of police officers on bicycles in plain clothes whom will radio the police vehicle up ahead for close passes by motorists.
Good you’re okay rojo. Lucky.
Training rides fly 6 and 12 cameras. For posterity.
Seemingly in lands where the car came first it’s screw the cyclist.
super slim
Zen MBB Master
The Cruzbike Family has shown again how compassionate and helpful they are for a family member in need!!!
RojoRacing
Donut Powered Wise-guy
How awesome is the cruzbike and bent community? Well how about our resident Polish seat fabricator aka Gregor aka Thor pulling a rabbit out of a hat and finishing a seat in less than a day so I have a chance at the race. Last I heard it would be a week then I get this these Pics and a message an hour ago Now lets see if the United Postal Service can carry through.
If you were on the fence about upgrading to a better seat this is just one more reason to support Gregor and his offerings.
Now lets see if the United Postal Service can carry through. If you were on the fence about upgrading to a better seat this is just one more reason to support Gregor and his offerings.
RojoRacing
Donut Powered Wise-guy
How awesome is the cruzbike and bent community? Well how about our resident Polish seat fabricator aka Gregor aka Thor pulling a rabbit out of a hat and finishing a seat in less than a day so I have a chance at the race. Last I heard it would be a week then I get this these Pics and a message an hour ago
Damn! That is outstanding! Looks like things are lining up to have you back riding before race day.
What color is the new frame? We’re you able to convince Marie to have a custom racer red painted for you?
ccf
Guru
I'll second that. I went down on chip seal yesterday (rear wheel lost traction), and my Thor seat made a terribly loud scraping/scratching sound as I slid to a stop. I figured for sure it was toast. RD hanger is bent. RD cable housing shredded. RD itself is probably not serviceable. The nut on my rear wheel QR looks like i put it up to a grinding wheel as does the end of my handlebar. But I can't find a single crack in my Thor seat.
